Marvel Bandsaw Introduction
TopNav_L_F
Products My Cart Service
TopNav_R_F
HomeSideNav_L_F

 

Industry Newsletters
read on >

Testimonials
read on>

WANTED: Used Equipment
read on>






Marvel Bandsaws


 

Saw Features:

 

  • 5HP Sensorless Vector blade drive 50-450 fpm.
  • Power rapid advance & rapid column return.
  • Automatic saw column retract.
  • Open lower bandwheel design for better chip control.
  • 60 degree tilting in both directions.
  • Optional Power tilt.
  • Blade stall/brake detection.
  • New improved blade tension
  • 1.25" blade
  • Patent pending Quick Change Column.
  • Patent pending Easy Load Guide Blocks.
  • 24VDC Controls.
  • State of the art controls.
  • All Siemens IEC contactors and control relays.
  • ABB IEC Fused Disconnect Switch, NFPA79 compliant.
  • State of the Art Siemens S7 PLC.
  • All 24 Volt DC Control.
  • Allen Bradley Push Buttons.
  • High Quality Sensorless Vector Drive.
  • UL 508a Listed Electrical Panel.

Saw Specifications:

 

Capacity @ 90˚ 18" (457 mm) Horizontal, 22" (558 mm) Vertical
Capacity @ 45˚Right 18" (457 mm) Horizontal, 14.5" (368 mm) Vertical
Capacity @ 45˚Left 18" (457 mm) Horizontal, 13" (330 mm) Vertical
Capacity @ 60˚ Left 18" (457 mm) Horizontal, 7.3" (185 mm) Vertical
Capacity with 3˚Cant 17.5" (445 mm) Horizontal, 22" (558 mm) Vertical
Blade Speed 50-450 fpm (15-137 m/min) infinitely variable
Feed Range 0-250 lbs. (64 kgf)
T-Slotted Work Table Work area 24.25" x 33" (616 mm x 838mm)
Table Height 34.5" (876 mm)
Bandwheel Diameter 19" (482 mm), cast iron wheels
Coolant System 21 gallons (79 liters)
Blade 15' 4" (4674 mm) long x 1.25" (32 mm) wide, .042" (1.07 mm) thick
Coolant Pump 1/8 Hp
Blade Drive Motor 5 HP (3.75 kw) 1800 RPM

 

Please click on the model numbers below for additional information regarding other Marvel bandsaws

 

MODEL
CAPCITY
BLADE
TILTING
FEATURES
2125PC 20"x25" 1.25" -60 to +60 Programmable PCII Controller
2125TS 20"x25" 1.25" -60 to +60 Graphical part programming. Windows based control. Shuttles from 4’ to 18’
8 MARK II 18"x22" 1.00" -45 to +45 Simple operation
8 MARK III 18"x22" 1.25" -60 to +60 Simple operation
81 17"x20" 1.25" -45 to +45 Programmable PCII Controller
25 25" x 37" STD Column
24" x 35" 3˚ Canted Column
1.50" -45 to +45 Programmable PCII Controller
2150PC 20"x25" 1.50" -60 to +60 Programmable PCII Controller
2150TS 20"x25" 1.50" -60 to +60 Graphical part programming. Windows based control.

 

 


HomeImage_R_F
BelowTop_B_F